Fast, licensed, and guaranteed. We solve the toughest Mobile Sandblasting problems in the Frisco area before they cost you thousands.
Frisco's rapid growth means new construction everywhere. But that growth brings a hidden enemy: silica dust, concrete splatter, and metal corrosion. Your equipment and structures take a beating from the Texas sun, high humidity, and the constant freeze-thaw cycles in winter.
That's not just cosmetic damage. It's structural decay. Rust creeps into steel beams, rebar, and machinery. Paint peels, exposing bare metal to the elements. Concrete spalls, creating trip hazards and safety issues.
You need a solution that comes to you. Mobile sandblasting is the answer. We bring the industrial power to your site, whether it's a commercial lot off the Dallas North Tollway or a residential property near Stonebriar Mall.
Don't wait until the damage is irreversible. Here are the warning signs that your property needs immediate attention:
We strip rust, old paint, and scale from heavy machinery, trailers, and structural steel. Our mobile rigs carry 185 CFM compressors and 600-pound blast pots. We use garnet or steel grit depending on the substrate. For delicate parts, we switch to glass beads or soda. We match the abrasive to the job—no guesswork.
We handle everything from a single axle to a 40-foot storage tank. We mask off sensitive areas like bearings and seals. We work around your schedule, even overnight if needed. The result is a clean, bare surface ready for coating. We leave no dust behind—we vacuum and contain the blast media.
Concrete needs a profile for coatings to bond. We use a shot blaster or scarifier for large slabs. For vertical surfaces, we use a sandblaster with a fine abrasive. We remove old sealers, paint, and contaminants. We can achieve a CSP 3 to CSP 5 profile, depending on your spec.
We handle driveways, patios, pool decks, and commercial floors. We also remove graffiti and stains. We protect surrounding areas with plastic and tape. We clean up thoroughly—no mess left behind. Your concrete will be ready for epoxy, stain, or sealer.
Corrosion is a silent killer. We strip rust down to bare metal using a combination of blasting and power tools. We then apply a rust inhibitor and a primer. We can also remove old coatings like lead-based paint, safely and in compliance with EPA regulations.
We use dustless blasting for sensitive areas. This method uses water to suppress dust and reduce heat. It's perfect for residential and commercial sites. We can also apply new coatings—epoxy, urethane, or zinc-rich primers. We ensure the surface is properly prepared for maximum adhesion.
That's the average price for a typical mobile sandblasting project in Frisco. But don't quote that as a fixed price. Every job is different. We base our quotes on square footage, material type, and the level of contamination.
Labor is the biggest cost. Our crew of two to three technicians runs about $150 per hour. A small project might take a day. A large one could take a week. Materials—abrasive, nozzles, and protective gear—add another 20% to 30%.
Cheap fixes fail. A $500 DIY sandblaster rental won't have the power or the containment. You'll end up with a poor surface profile and coating failure. We've seen it happen. We offer free estimates and detailed proposals. We stand behind our work with a warranty.
Don't let rust and corrosion eat your investment. Call us for a quote and see why we're the trusted choice in Frisco.
We start with a thorough site assessment. We check the substrate, measure the coating thickness, and identify any hazardous materials. We also test for moisture and salt contamination. This tells us exactly what we're dealing with.
We then provide a detailed written estimate. No surprises. We outline the scope, timeline, and cost. We also discuss safety protocols and containment plans.
We set up our mobile rig and contain the work area. We use tarps, plastic sheeting, and vacuum systems to keep dust from spreading. We select the right abrasive and nozzle for the job.
Our technicians are trained and certified. They work methodically, ensuring even coverage and the correct profile. We monitor the progress and adjust as needed.
After blasting, we inspect the surface with a profilometer. We make sure it meets the spec. We then apply the coating—primer, paint, or epoxy—using spray or roller.
We clean up the site, removing all debris and waste. We leave your property spotless. We provide a final report and warranty. Your surface is protected for years to come.
We cover all of Frisco, from the Star District to the Shops at Legacy. We're familiar with the local weather—hot summers, high humidity, and occasional ice storms. That's why we recommend coatings that withstand extreme temperature swings.
We work along the Dallas North Tollway, Preston Road, and the Sam Rayburn Tollway. We've done jobs at the Frisco Square, Stonebriar Country Club, and the Ford Center. No job is too big or small.